VEVOR Welding Table, 36" x 24" Adjustable Workbench, 0.12" Thick Industrial, 600lb Load Capacity, Heavy Duty Carbon Steel, Gray Steel With Accessories

I ordered the 24"x36" weld table. It arrived undamaged and had all the hardware. The Table top was Very poorly tacked welded to the angle iron supports on the under side. My 1st job on this table was to add more substantial Tack welds for better support. Assembly was easy, the table is much more sturdy than my old flimsy table. Dont expect the table top to be perfectly level, perfection is a lot more expensive. It is relatively heavy so you may need help to stand it up. $110 for this table is a great price. I am very pleased.

I didn't even read the reviews before I purchased. If I would have I might have been more skeptical in buying but I like deals and this one was too good to pass up.First off packaging absolutely terrible. The table is soo heavy in the process of shipping someone used duck tape on a section of the box because it ripped open. There was small holes and I almost thought that the stuff like screws fell out. The inside had foam to help with delivery~completely destroyed foam everywhere.The condition of the table after super easy to understand set up but took long to put together assembly because the table was made without attention to detail so the holes didn't line up. The legs seem flimsy but were able to withstand me (200lbs) on top. The table itself needs love. Its discolored and has sharp spots where the holes are.You might think this is a bad review why give it 5stars well my welding friend heres why.For the price! Way under $200 you wont find a better table to start with. It made it to my house with all parts included and even if it didnt I know they have good customer service to get things straightened out. The parts and gloves cheaply made but for dawm sure it will get any simple job done. This table was made by welders for welders and I couldn't be happier from this purchase.

Assembled in about 20 minutes with basic hand tools.Top is true and flat but one corner was bent from being dropped, it is bent down so it will be a non issue.Legs are thinner than I’d like, but should hold the 600lb it’s rated for.Came with plenty of nuts and bolts. Even some extra.Functionality wise it should do the job. I plan to add a piece of expanded metal on the leg supports for a light duty shelf.I was able to man handle it upright after assembly but consider having a helper.As far as the included accessories, you get a chipping hammer, wire brush, 4 x stamped metal c clamps, 12 different adapters for the clamps to help hold your piece, and a cotton pair of gloves I threw in the trash.

Was pleasantly surprised as to the thickness and quality of the top of this table .

Mixed feelings, but overall positive because of how cheap it was. For $110… I'd be hard pressed to get the material. It's a generally sturdy table, but does have quite a few flaws that might not be worth it to some people.*THE GOOD*- Value. For around $110, the value is unbeatable. An all steel 36x24in table that is fairly sturdy is good value.- Materials. All steel. Table top is about 3mm / .120-.140" thick on average. The legs and cross beams are about 1.5mm / .062" thick.- Included hardware is good quality. This is an area where the cheap, import products lacked previously. The hardware seems to be legit instead of the older stuff that would shear off when tightening (although I went up to 3/8-16 in a couple spots).- Ease of assembly. The table is easy to assemble with or without instructions and can be done in 20 minutes or less by oneself. ****THE BAD*- Deburring might as well be non-existent. I've spent a decade in a machine shop handling sharp parts and I still had to dig out a couple steel splinters. In the race to the bottom (price wise), they have gotten rid of as much manual labor as possible. This thing was covered in burrs that could have easily led to a wound that required stitches. They were everywhere. Bring your file, your die grinder, your dynafile, your chamfer drill, and your sandpaper.. you better believe you will need it all and about a hour of time to properly deburr this table. Wear gloves, take your time, and be careful.- Structural Issues. They have this thing rated at 1200lbs but given the low quality of the welds, I don't know if I'd go over 5-600lbs. I am considering running steel wire in an X pattern at the bottom of the legs and the top where the table mounts to help, but if you need 1200lb capacity, I may look elsewhere.Honestly, I've got mixed feelings. It was half the price of the next cheapest table, but it did require quite a bit of time and effort to "finish" it from deburring to throwing down another coat of paint afterwards. It'll serve it's purpose for me as the base for a small DIY CNC Router, but I guess it all comes down to how much time and effort are you willing to put into it? If you don't mind a hour or two into a little side project, it might not be a bad deal. But if you need something that you can use right out of the box, this certainly isn't that.Would I buy it again? I don't know. I'd at least consider the tables that are around $200 and come with the rolled edges on the table and certainly look more sturdy. I'd at least consider those a bit more.

Assembled the table, installed a JET 300 pound sheet metal brake / roller / shear on it. Weak & wobbly, ordered the correct table from JET. This table came with gloves ( garbage ) 4 clamps ( child's toys, Chinese trash ) and a wire brush that was coming apart in shipping. Lol. Pure junk. Waste of $125.00. I DO NOT RECOMMEND PURCHASING THIS TABLE.

very happy with this table

Table itself is just as described. Went together with ease, as long as you don't need directions they are a single sheet that has been copied enough times to be a grainy blur. Mine didn't have the sharp edges other people had mentioned. Sturdy enough without being to heavy to move around. The "accessories" are a waste, brush and "gloves" went straight into the trash bin. Clamps are fine, basic but effective. Overall I am happy with my purchase and am considering ordering a second one.