Bathroom Sink Drain,Drain Stopper Bathroom Sink with Overflow,Pop Up Drain Assembly with Detachable Strainer Basket,Built-in Anti-Clogging Strainer,Stainless Steel Brushed Nickel

This replaces a Home Depot sink stopper that did not perform well after a few years. This product avoids all of the issues the more expensive HD product, and was much easier to install.First, this product has a simple, removable stopper with a catcher. The HD one was non removable, got clogged, and couldn't be fixed. This has none of those issues.Second, the product has rubber gaskets and a simple large nut that screws on to be water tight. The HD one kept leaking water and was a bear to get it into position. This product was 10X easier to install and had no leakages.This product is also stainless steel tubing, with brass pieces in the catcher. Time will tell if there's rust, but probably not an issue.Finally, the only difference between this and other sink stoppers I've installed from HD, is that this one doesn't have an extension on the bottom to make it taller. It wasn't a big deal, since I had spare plastic tubing lying around I could cut (from HD products, years ago) to extend the compression fitting under the sink. The whole install process took ~30 minutes, including removal, cutting, and fitting. Had another person to help out in the install, though you could probably get by yourself due to the simplicity of the screwing nut holding everything into place.Overall, a great product. I'll buy another now, just in case I need a replacement in one of my other faucets. Highly recommended based on the install and water-proof result.

I recently installed this in my powder room. Installation was easy with no leaks. This is almost half the price of plastic drains and should hold up better as it is metal Functions as expected.

This drain was beyond easy to install. It looks great and works fantastic. Make sure to read product details not all drains are the same people. Check your measurements and know your pipe diameter and you will be fine and surprised at how easy the install is.

So I purchased two of these and installed them both today. I think the folks who have had trouble with leaks may have encountered an installation issue. You must pay attention to the location of the washers. There are no instructions with the product so you have to look at the videos on Amazon. The first one took a bit longer than the second but that was to be expected. Disassembly of the old system was really pretty easy but don't forget to put a pail underneath the trap or you will have a few ounces of water on the bottom of the cabinet which will be most annoying. The order of the washers: One of the larger washers has to go on the upper sink side and it goes in "cone shape" down.. The washers on mine were put on the device out of order. The flat washer goes on 2nd, on the underside of the sink, followed by the other larger washer and the "cone shaped" part of the second washer goes up. Screw on the gold metal part and hand tighten. It really is a thin piece so I can see how it might break if over tightened. Next slide the screw top that attaches to the trap followed by the washer on to the drainpipe and then insert the drain pipe into the front side of the trap. At this point you need to adjust the trap so that it fits on the drainpipe and the other side of the trap on the exit pipe. Tighten each of those a bit so you know that everything will screw together correctly. Then tighten the gold piece on the drain pipe. You really have to tighten it a lot to make sure you collapse the washer on the top side of the sink. It seems to take more tightening that one might expect but if you don't do it correctly, water will puddle in the sink because of the way it sits. It's possible that this is also where leaks can develop. Don't overtighten as you could break the gold piece at which point you will be out of business. Tighten enough to assure a good seal, but don't overdo it. Then tighten the the screw caps on both sides of the trap. Same rule. Tighten securely but don't over do it. Run the water and check for leaks. At this point everything should be good.One thing you need to know which is not clear from the pictures and I'm sure it will annoy some people. When you put the top piece in the drain pipe, as you know, you push it down to close the drain and do the same to release it. Mine held water without any issues. However, when that piece is not pushed down to allow the sink to fill, it sits a full 1/2 inch about the drain hole. It is also quite large and looks a bit strange in comparison to the one you just removed. Photo 1 shows the drain closed and photo shows it open. If you can't live with that, you may want to try a different product.Overall, the product is as described and works well. Installation is not difficult but you need to do it correctly. Finally, you have determine if you can live with the top sitting so high. It does not interfere with the water flow or cause any splashing. I'm really ok with it considering the relatively low cost and less than difficult installation process.I hope this is helpful.

This is made of metal and 1/2 the cost of finding something similar at a local hardware store or big box store. Easy to assemble and no leaks. The handy strainer is a plus and the pop top stopper works better than the original one that only lasted 2 years. I'm going to purchase more to have on hand for the other vanity sinks

Good price with no sacrifice in quality. Looks good, works well.

Easy to install and didn't even need plumbers putty. Works perfectly. And all metal.

The extra complexity of the original pop-up drain was causing clearance problems so I replaced it with this simpler push-button drain. It was inexpensive and the installation was pretty straight forward.

Muy bien producto, es de inoxidable y cumple perfecto su cometido.Lo instale sin herramienta gracias a qué su tuerca de bronce es gruesa y se puede manipular con la mano.

Acero inoxidable inoxidable, se ven de buena calidad

Fácil de instalar, llevo usándolo un pocoas de tres meses