DUST COMMANDERCyclone filter element/Dust collector

I bought the dust commander as a last ditch before looking at a larger and significantly more expensive dust extraction option for my workshop. It is the size of a small single garage so I do not have the space to have a large system. I was using a hoover on it’s own which would get clogged quickly with fine dust and clippings.The dust commander has exceeded the performance I would have expected. It came with 4 adapters that fit the existing vacuum I have in the workshop and the hoses I have. I have installed it on the top of a 30 litre air-tight plastic drum, bolting it to the lid of the drum. Very easy to install; although I may add a thin veneer of silicon sealant to the rubber gasket that comes with it to enhance the fit. I didn’t line the drum to start with which was a mistake, but a simple bin bag in there works well.I’m using a vax power 4 to drive it which I was concerned would not be powerful enough to really get it working, but it is running exceptionally well. I’m currently working with a lot of MDF and MR MDF which has horrible fibres so I have super impressed that the Vax has got barely anything in it. If you are considering using it in a similar manner to myself then it is worth replacing the filters in the vacuum whilst you’re at it.It has of course not negated the requirement for a proper breathing mask to protect me but everything that is near the inlets is getting sucked up. Because the whole setup is small it is very easy to manoeuvre around the workshop. I have tested the system cleaning the entire workshop which has removed the layer of dust over everything.In short, if you have a small workshop and don’t want to spend large amounts of money on a specialist system then this is the way forward. Great performance; great value for money.

Fitted the cyclone to a metal bucket for the shop vac. Seems too be well made and works well, collected the dust with no problems. Easy to install.

I started this after it was received and examined but not installed on anything. I've now got it up and running very successfully. Read on if you dare:Part 1 - package arrived.I know a bloke who has a dust deputy AND a dust mite. This looks like exactly the same moulding so I'll go and compare later. I know these things work, and work really well so now I need to finish my drop box.Great price on this listing, btw.The moulding seam grinding is a bit rough on the outside but the inside feels perfectly smooth as far as I can tell.Part 2I've now finished the drop box.I've heard a lot of warnings about inadequately strong containers and in fact one YouTube demo of the unit proudly mounted atop a paint bucket showed the bucket collapsing when the vac was switched. The author saying he's have to look into improving it seemed a good enough reason to avoid that route...SO:I overengineered my drop box, just for fun and produced an octagonal "drum" from 19mm pine, using birdsmouth construction (like a hollow ship's mast) with a snap-catch flat lid in 19mm pine and a plinth base made from a bit of mdf.I think it looks kinda cute, like something of a 19th century farm or some such... anyway, a black plastic Ikea wastepaper bin fits inside it and is an exact (really) fit top to bottom, making an airtight seal when the lid is snapped on.Because of the thickness of the lid, there is no need for a gasket or retaining ring on the inside of the lid.The biggest, totally unforeseen problem has been attaching hoses.The infeed is a Bosch 35 mm hoseBosch VAC005 5-Meter Vacuum Hose 35mm which I had to get from Amazon dot COM and cost about 36 quid delivered. The Festool equivalent, here,FESTOOL 452884 Suction hose D36 antistatic D 36x5m-ASPrice: £132.95The difference? The festool is antistatic and is a different colour.going off to my tools, and the bosch machine fitting _just_ goes onto the Dust Commander spigot but it's unfeasibly tight and doesn't go on far enough to be really secure. I'm also not confident about the fitting not splitting, it really is _that_ tight.I therefore sat down with several cups of coffee and an excuse to listen to some Arvo Part on Radio 3 and tediously filed the input (side) spigot into a taper. This was easier than it sounds. I just used light strokes and wandered around the entire circumference a dozen strokes at a time, repeating the process over and over again and pausing now and again to try the hose fitting again.How long did it take?Two complete Arvo Part symphonies, Vaughan Williams Fantasia on Greensleeves, the whole of Scheherezade (Rimsky Korsakov - bloody marvellous!) and most of Let it Bleed which I'm sure everybody knows as it's the Stones' finest album, ever.At the end of that the hose fitting was still a very tight push fit but felt hundreds of percent better, progressively tightening as pushed on with a bit of a twist.There's no chance of it coming adrift accidentally and it no longer feels like it's stressing the coupling to fracture-point.The Dust Deputy, of course, already has a manufacturer's moulded-in taper. The Dust Commander and the identical-seeming Dust Mite do not.The Deputy is an expensive PITA to get hold of in the U.K. The Dust Commander's lack of taper can be overcome with very few special tools ( a file and a load of music) but it would have been nice to have had it ready to go out of the box.If you're going to slip a hose INSIDE the spigots, then _this_ is not a problem.Lungs of the outfit are provided by an AquaVac which a mate of mine found in a skip and left on my doorstep, saying he thought the bottom part might be useful as a drop box.I fired it up. It didn't work. I put a new fuse in it. The motor worked but there was no suction, so I dynarodded the hose out with an inch square batten and removed the filter which was blocked so thoroughly that air would literally not flow at all. Some oik seems to have used it to clean up plaster without a dust bag, wrecked it and chucked it in the skip.Patience and a little Mozart is all it took, though I found some Norwegian Death metal necessary for cleaning the worst of the hose out. Thank you Tristania.The Aquavac has oodles of suck.but the hose is a bit feeble. It's around 30 mm. I think and after loads of reading I'm convinced a fatter vac to cyclone hose would give me better performance.I managed to get it to go into the top port of the Cyclone by cutting the thin tapered tool end off and ramming the bare hose up a piece of plastic I found that was a tight push into the spigot's I.D. I secured the hose itself with duct tape wrapped around some abrasive paper to make it fit inside this "adapter". The whole thing was then held together with more duct tape carefully lapped around the hose ribbings. Tedious, but managed with the help of some Debussy and a little Jefferson Airplane.Now I have a push-fit top connector that can be coupled and uncoupled as necessary.In the long term I'd like to replace the cyclone-to-vac hose with something like 65mm instead of the 30 or so it has now, but then there's going to be all the problems of adapters again and I'm NOT going to pay 150 quid for the Festool made to measure part. I might also buy a new filter for the Aquavac as the one in it has been brushed out and whacked to clean it and it's a bit past its best and it really is the bit that keeps the invisible dust out of the operator's pipes.Anyway, it works and it looks... unusual.I made the family come out and watch the entertaining cyclone as punishment for the constant "What is THAT you're making?" interrogation I'd suffered over the weeks I'd half-heartedly done bits and pieces on the project. Now they know, and are careful not to ask any more.Oh - the vac is plugged into a cheap adapter sold for powering up computer peripherals when the main unit is booted. Instead of a computer, it now has a track saw or sander going into the "main" socket and the Aquavac going into one of the two auxiliary sockets. There's a 5 second delay on starting and a 5 second run-on when the tool stops, which is plenty of time to clear the hoses.I suppose I ought to put some photographs up on the page to make sense of the rambling explanation. Watch this space.I've knocked one star off purely because of the taper issue. The unit performs flawlessly otherwise.

Definitely the answer if you're fed up dealing with disposable bags for your wet/dry vac. I use this in my workshop with sawdust and wood chips, and very, very little actually gets past it to the vacuum. Just be sure to empty whatever barrel you have this mounted to before it gets too full, as the cyclone action is better with a bit of "space" beneath it in the barrel.No reduction in the suction power and it captures just about everything.

Bought for home workshop dust collection. Fitted to a steel bin and included a pressure relief valve. It all works well

Good price and makes a huge difference to dust extraction, filters last longer, don't have to empty the bag so often and saves on vacuum bag costs, so saving cost straight away. I was changing bags 2x day, now I am doing it 1x week. I could do with one with a 100mm inlet but struggling to find one ATM.

Very sturdy and works brilliantly !! . Using with 18v Milwaukee vac .

Well made product that works really well. I have attached it to a 25 litre steel drum with quick release lid and have no issues with the suction causing collapse as some have found using plastic barrels. This was not the cheapest cyclone for sale online but the extra cost is worth it as this is a proper, well made item that feels strong and durable. Highly recommended. Very happy with it. The seller gave excellent after sales support too and sent some installation and user instructions and tips. I didn't need them but this was a nice touch from a seller who clearly cares.

The media could not be loaded. Ich bin sehr zufrieden mit dem Produkt. Der Versand war schnell und die Qualität des Materials ist sehr gut. Hier ein Überblick über mein Setup:Staubsauger: Nilfisk Alto Attix 3 mit Vlies-StaubsaugerbeutelFass: 120-Liter-Fass, verstärkt mit einem MetallringAbsaugung: 50-mm-Schlauch für die AbsaugungDie Montage des Zyklon-Abscheiders dauerte etwa 5 Minuten, und der mitgelieferte Bohr-Aufkleber hat das Bohren deutlich erleichtert.FazitDer Abscheider besteht aus hochwertigem, flexiblem Kunststoff, der nicht brüchig ist.Funktioniert tadellos – für ein volles 120-Liter-Fass habe ich nur zwei Vlies-Staubsaugerbeutel gebraucht.Beim Arbeiten mit Beton (z. B. beim Schneiden oder Fräsen) hilft es, den Staubsaugerbeutel ab und zu zu schütteln, um die Saugleistung konstant zu halten.Ich habe festgestellt, dass die Leistung besser ist, wenn zwischen Zyklon und Staubsauger ein etwas dünnerer Schlauch verwendet wird.Zubehör ist großartig, ich musste nur noch einen zusätzlichen 5 Meter langen 50-mm-Schlauch kaufen und daß was.Das 120-Liter-Fass ist super praktisch und ermöglicht längeres Arbeiten ohne häufiges Entleeren. Allerdings sollte man das Gewicht des vollen Fasses nicht unterschätzen.Insgesamt bin ich wirklich beeindruckt – ein so einfaches Teil und eine so großartige Wirkung! Absolute Kaufempfehlung.

Me ha gustado el precio y la calidad del producto. Es de plástico grueso y parece duradero, pero al margen de eso funciona de maravillas. Mi había es la carpintería y compre este ciclón porque tenia que limpiar el aspirador todos los días, ahora con el ciclón DUST COMANDER se me ha acabado el problema. He puesto un recipiente grande y puedo trabajar varios días sin tener que limpiarlo. El aspirador ni se entera del polvo. Lo recomiendo 100 x 100.

Köpte en ny grovdammsugare, tog då den gamla dammsugaren och monterade på detta cyklonfilter. Dammsugde sedan ett smutsigt garage, cyklonfiltret tog hand om typ 90%, även små dammpartiklar konstigt nog. Rekommenderas.

It 's installed between my sandblaster cabinet and my shop vac. The adapters are also very usefull to connect the pvc piping and the vac.

Hiermee is de zuigkracht van mijn stofzuiger een stuk beter voor veel langere tijd.