Edge Supply Birch 24 x 96-inch Flat Cut, 3M Peel and Stick Wood Veneer Sheet – Self-Adhesive Wood Veneer, A Grade, Smooth-Finished – Versatile for Furniture Restoration, Cabinetry & DIY Use

Beautiful material, thick with the backing and easy to work with, with the 3M Peel & Stick.I was creating Shaker-Style End Panels for my cabinets - Real White Oak Rails & Stiles and the veneer over 1/4 birch plywood for the center panels.A couple of installation notes that are important.First, I gave the Plywood two coats of Water-Based Polycrylic with a light 240 grit sanding. This will give much better adherence to the Veneer 3M coating by sealing the Ply to a smooth surface.Then, it's best to be in a warm environment. A bit cool in my basement workshop, so I applied upstairs in a heated room at about 70FNext, when you apply it is critical that you apply pressure across the Veneer - it's important to know that the adhesive is PRESSURE activated. But additionally, you need to ensure all the bubbles are worked out before it sets up. I used a combination of a carpet-tucking tool and a J-Roller. Roll/Push from center out initially in both planes. I found I could hear a 'Rice Krispies' type of popping as I pushed small bubbles (these were not visible, the only indication was the audible response as you 'pressed' them.)Once confident it was pretty well , at least initially, secured, I flipped and trimmed it. Blade with the grain and, although you can cross cut with multiple blade strokes, a veneer saw gives much cleaner cut in that plane. An alternative to a specific Veneer saw could be a Japanese Pull Saw, blade with a finer, higher tooth count.Then flipped back over and worked the veneer surface some more with heavy pressure from the J-Roller, especially towards the edges. The now combined panels will be cut to final size on the table saw and given a final finish or Rubio Monocoat.Some reviews stated they had bubbles - in my opinion the Bubbles are due to inadequate preparation and application technique. This adhesive is fabulous but can only work as well as it will be applied.

Your gracious and have a very nice product

Our dishwasher was leaking, and we didn't realize it until the laminate started warping When we took the molding off the bottom of the cabinet, we saw that the side of the cabinet was moldy. After cleaning it up, we were able to match the wood texture with this veneer. Easy to apply. We stained it, and it looks great!

Peel and stick sheeting is so easy to work with, cuts with a good pair of scissors or razor knife to work in most any project. The peel and stick adheres very well and turned my old banged up cabinets into a great new look!My only complaint/warning that knocked it down a star is that it did not take to polyurethane the same way other veneer sheets or lumber of the same species... (different manufacturers') possibly because of the pre-applied peel and stick trapping air? but a little pre-staining made the difference, just not something I needed to do on other products. staining is a caution helpful tip

Worked great for my application easy to use and took stain well.

I bought this for refinishing two bathroom vanities in my houses. The cabinet and doors and solid wood so I was able to sand those and stain them but the side is a printed wood grain on plastic like sheeting. I got this veneer to cover the sides.The product looks good but is very hard to work with and the edges curl up no matter how hard I push to try to get the adhesive to stick. I am going to to have to get some super small trim pieces to hold down the edges, not sure how that is going to work but I can’t think of anything else.

High quality!

This arrived rolled up in the sturdy packaging. It took a couple of days to get it to flat now where I could work with it. The 3M pre-applied adhesive works great, just be sure that you’ve got it positioned exactly where you want it. I have a coffee table that I purchased inexpensively and the top was wearing through the contact paper. (I should’ve known it wouldn’t be real wood when I bought it so cheaply.) anyhow I prepared the surface and laid this down. trimmed edges stained it to match and it looks like a much more expensive piece of furniture now. I’m already thinking of other things I could use it for in the future.