Sunco 4 Pack 50W 7 Inch LED Commercial Industrial Warehouse Workshop Prisma Wraparound Light, 6500 Lumens, 3 CCT 4000K Cool White/5000K Daylight/6000K Daylight Deluxe, Non-Dimmable, AC120-277V - ETL.

After a recent move, i had to create a shop in the garage, shared with my wife's car:( . These lights were easy to connect into the existing switch and bulb socket wiring. Spaced about 7 feet apart, they provide excellent lighting for all of my equipment at a very good price. Adjustable color temperature is a great feature. I used 4000k (which they were shipped at) as the brighter options created glare and a very artificial look to everything.

Looking back, I should have gone with lights that had a chain mount and came with connecting cables. I was too focused on price. To complete the project, I had to buy shielded cable and a junction box to hardwire all four to each other. Which was additional $$. Also, flush mounting turned out to be a moderate pain in the [butt].SO, plan your project COMPLETELY in advance before you buy. If you are connecting the units to each other, pre-fab connecting cables will be much easier (assuming they are long enough).But, listen, these are fine lighting units. They are exactly as described. My project was an (eventual) success and I have no complaints about these lights themselves.

These lights are great! Easy to install and WOW what difference they make. I'm so glad I purchased these lights. Now my Intier garage is lit up.

We bought 4 of these and love our new garage lights! They are lightweight, thin, and easy to handle. Much brighter than the 4 fluorescent fixtures that we replaced, and less expensive to operate too! Although we haven't yet used the feature that allows you to link multiple units together, I think its a great idea and I'm thinking of purchasing more of these just to do that! If I had to come up with suggested improvements, they would be these: 1. I wish there were additional mounting holes near the center - if the junction box's holes don't line up in the direction you want to fixture to go, you'll have to drill new holes in the fixture in order to rotate it - not a big deal, but it would be nicer if you didn't have to. 2. There are no punch-out holes in the center of the unit, and that's where you would most likely feed the wiring through. There is a hole, but its small and if you have multiple units tied together in-line, like I do, in total they'll be too wide for that hole, so I had to enlarge the hole with a drill. Not a problem, but still. 3. The ends of the fixture's wires have a rubber-like shrink wrap on them, I assume to protect them. But I saw that as both unnecessary and as being in the way when trying to trim the insulation off the tips. I'd rather the wires already be trimmed, bare, and ready to connect. Again, all those are minor quips - I am VERY happy with my new lights!

I just purchased 8 of these shop lights. I am very impressed with the quality of the product and the amazing amount of light produced. I had 2 problems. First, 3 of the fixtures arrived with one broken tab on the transformer housing. I tried super glue to reattach the tab, but could not get it to stick. I ended up taping it with strapping tape which seems like it will hold. My biggest issue is that there is not a 2" center hole for the wiring. The florescent fixtures I am replacing have a 2" center hole with a supplied white metal cover to close off the hole after wiring. I am installing the fixtures on a very high vaulted ceiling which requires the use of scaffolding. I installed the first 4 very awkwardly by attaching the higher end with a partially screwed in 10" screw and the lower end with a 4" screw to support the fixture below the ceiling and allow me to get my hands above it to connect the wires. I then had to carefully work the wires most of the way into the box and making sure to align the wires to push all the way in when I fastened the fixture permanently in place. This procedure is incredibly time consuming when done on scaffolding.I decided to order a 2" metal cutting hole saw before installing the last 4 fixtures. Since I couldn't find one locally, I will had to wait 4 days for it to be delivered before I could complete the installation.If the manufacturer corrects the identified problems, these lights will be a perfect 5 star product. I still highly recommend them, but order a 2" metal cutting hole saw with them.

I was dreading this job. I did not want to stand on a ladder for two hours trying to find my garage ceiling studs. This product is so light you don't need studs. You simply go to Home Depot, pick out some new generation dry wall anchors and you can hang this light anywhere. Each lamp weighs approximately 6 pounds. They are super light.These things are GREAT. I put four on one light circuit (you can have up to five) and with the flip of a switch my LEDs throw off so much light, I could do dental surgery in my garage. I don't know how I lived with such a poorly lit garage for so many years. Another cool feature of these lights is the dongle that each light comes with. The dongle is about six inches long and allows you to daisy chain your second light in that row, by plugging the dongle into the first light. Wire one light and light TWO. Overall, extremely happy with this product. MONEY WELL SPENT. I am now looking forward to ridiculously long life span on my LEDs. No warm up time either...they are instant ON.

Easy installation and very bright